Cirrus Logic Madera class audio codecs switch driver The switch configuration settings are a child node of type "cirrus,accdet" within the parent MFD driver devicetree binding. See Documentation/devicetree/bindings/mfd/madera.txt This node contains one or more child nodes to describe the accessory detect configuration. Mandatory properties: - #address-cells : must be 1 - #size-cells : must be 0 Child node mandatory properties: - reg : output number this configuration applies to, 1=OUT1, 2=OUT2, ... Child node optional properties: - cirrus,micd-pol-gpios : GPIO specifier for the GPIO controlling the headset polarity if one exists - cirrus,micd-detect-debounce-ms : Additional software microphone detection debounce specified in milliseconds - cirrus,micd-manual-debounce : Additional software button detection debounce specified as a number - cirrus,micd-bias-start-time : Time allowed for MICBIAS to startup prior to performing microphone detection, specified as per the MICD_BIAS_STARTTIME bits in the register MIC_DETECT_1 - cirrus,micd-rate : Delay between successive microphone detection measurements, specified as per the MICD_RATE bits in the register MIC_DETECT_1 - cirrus,micd-dbtime : Microphone detection hardware debounce level, specified as per the MICD_DBTIME bits in the register MIC_DETECT_1 - cirrus,micd-timeout-ms : Timeout for microphone detection, specified in milliseconds - cirrus,micd-force-micbias : Force MICBIAS continuously on during microphone detection and button detection - cirrus,micd-software-compare : Use a software comparison to determine mic presence - cirrus,jd-invert : Invert the polarity of the jack detection switch - cirrus,jd-use-jd2 : Use JD2 input with JD1 for dual jack detection. - cirrus,jd-wake-time : Specifies a length of time that a wake lock will be held for during jack detection operations. - cirrus,gpsw : Settings for the general purpose switches, set as per the SWn_MODE bits in the GP Switch 1 register. First cell is the value for the SW1_MODE Second cell is the value for the SW2_MODE (cs47l90, cs47l91, cs47l92, cs47l93) - cirrus,fixed-hpdet-imp : Do not perform any headphone detection, just use the fixed value specified here as the headphone impedance. Value is in hundredths-of-an-ohm (ohms * 100) - cirrus,hpdet-ext-res : Impedance of external series resistor on hpdet. Value is in hundredths-of-an-ohm (ohms * 100) - cirrus,hpdet-short-circuit-imp : Specifies the maximum impedance in ohms that will be considered as a short circuit - cirrus,hpdet-channel : When this property is set then right channel is used for headphone impedance measurement else the left headphone channel is used - cirrus,micd-clamp-mode : Specifies the logic of the micdetect clamp block - cirrus,hpd-pins : 4 cells specifying the clamp and sense pins to use. where clamp_x is the clamp pin for channel x and sense_x is the impedance sense pin for channel x, as per the HPD_OUT_SEL field of HEADPHONE_DETECT_0 register. A value >0xFFFF means use the default. (cs47l15, cs47l90, cs47l91, cs47l92, cs47l93) - cirrus,micd-ranges : Microphone detection level and key configuration, this field can be of variable length but should always be a multiple of 2 cells long, each two cell group represents one button configuration The first cell is the maximum impedance for this button in ohms The second cell the key that should be reported to the input layer - cirrus,micd-configs : Headset polarity configurations, variable length but must be a multiple of 5 cells, each two cell group represents one polarity configuration first cell is the value of ACCDET_SRC register field (CS47L35, CS47L85, WM1840), MICD_SENSE_SEL register field (all other codecs) second cell is the accessory detection ground as per the MICD_GND_SEL register field the third cell is the MICBIAS to be used as per the MICD_BIAS_SRC register field fourth cell is the value of the micd-pol-gpio pin, a non-zero value indicates this should be on fifth cell is set to zero (cs47l35, cs47l85, wm1840) value of HPn_GND_SEL register field (all other codecs) - cirrus,moisture-pin : The pin on which the moisture detection should be run. For (cs47l35, cs47l85, wm1840) this should be set to MADERA_ACCDET_MODE_HPx, for (cs47l90, cs47l91) this should be set to MADERA_HPD_SENSE_x. - cirrus,moisture-imp : The impedance threshold above which a detection will be considered moisture rather than a valid jack detection. - cirrus,moisture-debounce : The number of debounce measurements to perform on the moisture detection. - cirrus,init-delay-ms : Add a delay after jack detection in mS - cirrus,hs-mic: Specify an input to mute during headset button presses: 1 - IN1L, 2 - IN1R, ..., n - IN[n]R Example: codec: cs47l85@0 { compatible = "cirrus,cs47l85"; cirrus,accdet { #address-cells = <1>; #size-cells = <0>; acc@1 { reg = <1>; cirrus,micd-pol-gpios = <&gpio 0> cirrus,micd-detect-debounce-ms = <10>; cirrus,micd-bias-start-time = <0x1>; cirrus,micd-rate = <0x1>; cirrus,micd-dbtime = <0x1>; cirrus,micd-timeout-ms = <10>; cirrus,micd-force-micbias; cirrus,micd-ranges = < 11 0x100 28 0x101 54 0x102 100 0x103 186 0x104 430 0x105 >; cirrus,micd-configs = < 0x1 0 1 0 2 0x0 0 2 1 2 >; cirrus,fixed-hpdet-imp = <8>; cirrus,micd-clamp-mode = <0xb>; cirrus,gpsw = <0x3>; }; }; };