# # sensor drivers configuration # config SENSORS_SYSFS tristate "Sensors sysfs" help Support sysfs for sensors. If you say yes here you get sysfs support for sensor factory test. To compile this driver as a module, choose M here: the module will be called sensors_core. config SENSORS_SSP tristate "Sensors ssp" default n depends on I2C help ssp driver for sensor hub. If you say yes here you get ssp support for sensor hub. To compile this driver as a module, choose M here: the module will be called ssp. config SENSORS_SSP_ATMEL tristate "Sensors ssp ATMEL" default n depends on SPI help ssp driver for sensor hub. If you say yes here you get ssp support for sensor hub. To compile this driver as a module, choose M here: the module will be called ssp. config SENSORS_SSP_AK8963C tristate "Sensors ssp ak8963c" default n depends on I2C help ak8963c file for factory test in ssp driver. If you say yes here you get ak8963c support for factory test. To compile this driver as a module, choose M here: the module will be called ssp. config SENSORS_SSP_YAS532 tristate "Sensors ssp yas532" default n depends on I2C help yas532 file for factory test in ssp driver. If you say yes here you get yas532 support for factory test. To compile this driver as a module, choose M here: the module will be called ssp. config SENSORS_SSP_ACCELEROMETER_POSITION int "Accelerometer Sensor Mounting Position on Board" depends on SENSORS_SSP default "0" help X Y Z axis position. 0: X, Y, Z 1: Y,-X, Z 2: -X,-Y, Z 3: -Y, X, Z 4: -X, Y,-Z 5: Y, X,-Z 6: X,-Y,-Z 7: -Y,-X,-Z config SENSORS_SSP_GYROSCOPE_POSITION int "Gyroscope Sensor Mounting Position on Board" depends on SENSORS_SSP default "0" help X Y Z axis position. 0: X, Y, Z 1: Y,-X, Z 2: -X,-Y, Z 3: -Y, X, Z 4: -X, Y,-Z 5: Y, X,-Z 6: X,-Y,-Z 7: -Y,-X,-Z config SENSORS_SSP_MAGNETOMETER_POSITION int "Geomagnetic Sensor Mounting Position on Board" depends on SENSORS_SSP default "0" help X Y Z axis position. 0: X, Y, Z 1: Y,-X, Z 2: -X,-Y, Z 3: -Y, X, Z 4: -X, Y,-Z 5: Y, X,-Z 6: X,-Y,-Z 7: -Y,-X,-Z config SENSORS_SSP_SENSORHUB tristate "Sensors ssp sensorhub" default n depends on I2C help ssp sensor hub driver for sensor hub. If you say yes here you get ssp support for sensor hub. To compile this driver as a module, choose M here: the module will be called ssp. config SENSORS_SSP_FACTORY tristate "ssp factory" depends on SENSORS_SSP default n help ssp sensor hub driver for factory test. If you say yes here you can enable fatory drvier for factory test. To compile this driver as a module, choose M here: the module will be called ssp. config SENSORS_SSP_C12SD tristate "Sensors ssp C12SD" default n depends on SENSORS_SSP help This is for GUVA_C12SD UV Sensor device driver. GUVA_C12SD is made by Genicom. If you say yes here you get c12sd support. If you say no here c12sd will not be supported. config SENSORS_SSP_BOUNCE_FIRMWARE tristate "Sensors ssp BOUNCE_FIRMWARE" default n depends on SENSORS_SSP_STM help This is for Bounce firmware support. If you say yes here you get bounce firmware support. If you say no here bounce firmware will not be supported. config SENSORS_MAX86900 tristate "MAXIM MAX86900 HRM Sensor" default n depends on I2C help If you say yes here you get support for the MAX86900 HRM sensor. This driver can also be built as a module. If so, the module will be called max86900. source "drivers/sensorhub/atmel/factory/Kconfig"