############################################################################### # NFC Configuration for NON-HAL component S3FWRN5 # Samsung Electronics, System LSI Division # Update Date : 2015/01/05 # Region : All region # F/W Version dependency : NONE # This file contains below # 1) Default routing information # 2) Partial AID setting # 3) UICC listen tech mask # 4) Listen tech mask for P2P # 5) Poll tech mask # 6) eSE warm reset # 7) Other Information ############################################################################### # Application options #APPL_TRACE_LEVEL=0xFF #PROTOCOL_TRACE_LEVEL=0xFFFFFFFF APPL_TRACE_LEVEL=0x05 PROTOCOL_TRACE_LEVEL=0x1FFFFF ############################################################################### # File used for NFA storage NFA_STORAGE="/data/nfc" ############################################################################### # Maximum Number of Credits to be allowed by the NFCC # This value overrides what the NFCC specifices allowing the host to have # the control to work-around transport limitations. If this value does # not exist or is set to 0, the NFCC will provide the number of credits. MAX_RF_DATA_CREDITS=1 ############################################################################### # Allow UICC to be powered off if there is no traffic. # Timeout is in ms. If set to 0, then UICC will not be powered off. #UICC_IDLE_TIMEOUT=30000 UICC_IDLE_TIMEOUT=60000 ############################################################################### # Configure the maximum number of SE (UICC , eSE , DH) #NFA_MAX_EE_SUPPORTED=3 (DH, UICC, eSE), 2 (DH, UICC) NFA_MAX_EE_SUPPORTED=3 ############################################################################### # Configure the single default SE (mActiveSe) to use. The default is to use the first # SE that is detected by the stack. This value might be used when the phone # supports multiple SE (e.g. UICC : 0x03 and eSE : 0x02) but you want to force it to use # one of them (e.g. 0x03). ACTIVE_SE=0x02 ############################################################################### # Configure the default route (mDefaultEe) for ISODEP. # supports multiple SE (e.g. DH : 0x00 , UICC : 0x03 and eSE : 0x02) DEFAULT_ISODEP_ROUTE=0x03 ####################################################################################### # Configure the default "off-host" AID route. The default is 0x03 DEFAULT_OFFHOST_ROUTE=0x03 ############################################################################### # Configure the default Destination Gate & PIPE used by HCI (the default is 4, which # is the ETSI loopback gate. NFA_HCI_DEFAULT_DEST_GATE=4 NFA_HCI_DEFAULT_STATIC_PIPE_ID=0x72 NFA_HCI_SECONDARY_STATIC_PIPE_ID=0x71 ############################################################################### # Configure the NFC Extras to open and use a static pipe. If the value is # not set or set to 0, then the default is use a dynamic pipe based on a # destination gate (see NFA_HCI_DEFAULT_DEST_GATE). Note there is a value # for each UICC (where F3="UICC0" and F4="UICC1") # for each UICC (where 03="UICC0" and 02="UICC1 / eSE") NFA_HCI_STATIC_PIPE_ID_02=0x72 NFA_HCI_STATIC_PIPE_ID_03=0x72 ############################################################################### # Force UICC to only listen to the following technology(s). # The bits are defined as tNFA_TECHNOLOGY_MASK in nfa_api.h. # Default is NFA_TECHNOLOGY_MASK_A | NFA_TECHNOLOGY_MASK_B. #UICC_LISTEN_TECH_MASK=0x03 ############################################################################### # Force only poll to the following technology(s). #POLLING_TECH_MASK= NFA_TECHNOLOGY_MASK_A | NFA_TECHNOLOGY_MASK_B ############################################################################### # When disconnecting from Oberthur secure element, perform a warm-reset of # the secure element to deselect the applet. # The default hex value of the command is 0x3. If this variable is undefined, then # this feature is not used. #OBERTHUR_WARM_RESET_COMMAND=3 ################################ # Select controller support for AID matching # the default value is 0. # 0 Exact matching only # 1 Exact+Prefix matching # 2 Prefix matching only AID_MATCHING_MODE=0 ############################################################################### # Choose the presence-check algorithm for type-4 tag. If not defined, # the default value is 1. # 0 NFA_RW_PRES_CHK_DEFAULT; Let stack selects an algorithm # 1 NFA_RW_PRES_CHK_I_BLOCK; ISO-DEP protocol's empty I-block # 2 NFA_RW_PRES_CHK_RESET; Deactivate to Sleep, then re-activate # 3 NFA_RW_PRES_CHK_RB_CH0; Type-4 tag protocol's ReadBinary command on channel 0 # 4 NFA_RW_PRES_CHK_RB_CH3; Type-4 tag protocol's ReadBinary command on channel 3 PRESENCE_CHECK_ALGORITHM=3 ############################################################################### # Vendor Specific Proprietary Protocol & Discovery Configuration # Set to 0xFF if unsupported # byte[0] NCI_PROTOCOL_18092_ACTIVE # byte[1] NCI_PROTOCOL_B_PRIME # byte[2] NCI_PROTOCOL_DUAL # byte[3] NCI_PROTOCOL_15693 # byte[4] NCI_PROTOCOL_KOVIO # byte[5] NCI_PROTOCOL_MIFARE */ # byte[7] NCI_PROTOCOL_CLT */ # byte[8] NCI_DISCOVERY_TYPE_POLL_KOVIO # byte[9] NCI_DISCOVERY_TYPE_POLL_B_PRIME # byte[10] NCI_DISCOVERY_TYPE_LISTEN_B_PRIME NFA_PROPRIETARY_CFG={00:81:82:80:8A:81:90:70:74:F4}